Kenmore 9082, 46-9082 Refrigerator Water Filter Replacement
Bottom-freezer Kenmore or Kenmore Elite, and the filter's tucked into a tray you have to twist and lower rather than eject or slide? That's the 9082, and it happens to carry the widest contaminant coverage of any Kenmore filter in the lineup.
Confirm You Need the 9082
| Part Number | Also Known As | Install Type | Best For |
|---|---|---|---|
| 9082, 46-9082 | EDR2RXD1, W10413645A, W10413645, W10609378 | Twist-out tray | Kenmore and Kenmore Elite bottom-freezer models |
| 9081, 46-9081 | — | Eject-and-slide | Standard Kenmore side-by-side, bottom, and top freezer models |
| 9083, 46-9083 | — | Push-button eject | Select Kenmore side-by-side models |
If your filter lives behind a tray cover with a locking tab rather than a simple push or eject slot, you're almost certainly looking at the 9082.
Compatible Refrigerator Models
This filter reaches beyond Kenmore's own badge, which isn't typical for most codes in this lineup:
- Kenmore and Kenmore Elite bottom-freezer refrigerators
- Select Jenn-Air refrigerators using the EDR2RXD1 filter
- Select KitchenAid refrigerators using the same filter code
- Select Amana, Maytag, and Whirlpool models using EDR2RXD1
Always confirm your model number before ordering. This list is representative, not exhaustive, across the full compatible range.
How This Filter Actually Helps
The 9082 is the only Kenmore filter carrying NSF 401 certification in addition to NSF 42 and 53, which means it's been tested against a broader set of contaminants than most of Kenmore's lineup, including trace volatile organic compounds and asbestos fibers alongside the usual chlorine and lead reduction. That third certification tier matters if you're on well water or municipal water in an area with older infrastructure, since it covers concerns standard filters don't test for at all. Combined with a 0.6 to 0.75 GPM flow rate, it's built to keep dispenser performance steady rather than trading filtration depth for speed.
Kenmore 9082 vs 9081: Coverage vs Simplicity
| Kenmore 9082 | Kenmore 9081 | |
|---|---|---|
| Install Type | Twist-out tray | Eject-and-slide |
| Certification | NSF 42, 53, and 401 | NSF 42 and 53 |
| Filter Capacity | 200 gallons | 300 gallons |
| Cross-Brand Compatible | Yes, Jenn-Air, KitchenAid, Whirlpool | No |
| Best For | Bottom-freezer models needing broader contaminant coverage | Standard Kenmore filter housing |
How Do I Check My Part Number?
Start by looking at how your current filter is housed. A tray you lower and twist, secured by a locking tab, points strongly toward the 9082. From there, check the label directly, and if it's showing EDR2RXD1 or W10413645A instead of 9082, that's expected, those are the same filter under a different brand's part number since this code crosses over into several other manufacturers.
What Happens If I Order the Wrong One?
The twist-out tray mechanism is specific enough that a filter built for eject-and-slide or push-button housings simply won't seat in the 9082's tray at all. There's little risk of a partial, leaky fit here, the mismatch shows up immediately as a filter that won't lock into the tray, rather than something you'd only notice after water starts tasting off.
How Often Should You Replace This Filter?
Replace the 9082 every 6 months or 200 gallons, whichever comes first. Because its capacity sits lower than some other Kenmore filters, households running the dispenser heavily may hit that 200 gallon mark well before six months rolls around, so it's worth paying attention to usage rather than only watching the calendar.
What Customers Say
"Tray design took a second to figure out the first time, but it's simple once you've done it once."
"Water tastes noticeably cleaner since switching to this from a generic filter, worth the NSF 401 certification alone."
Buy With Confidence
Free shipping across the USA 30 days to return it if it isn't the right one NSF 42, 53, and 401 certified, independently verified Fast processing so your dispenser is back to normal quickly
Installing Your Kenmore 9082 Filter
- Release the locking tab on the filter housing tray inside the refrigerator
- Lower the tray cover and twist the old filter counterclockwise until it stops
- Pull the old filter straight out and discard it
- Insert the new 9082 filter into the tray
- Twist clockwise until it locks firmly into place
- Close the tray cover until the locking tab snaps back
- Flush 4 gallons of water through the dispenser before drinking, then reset the filter indicator
Ready to Order?
Get the Kenmore filter with the broadest contaminant coverage in the lineup, priced below what you'd typically pay elsewhere.
Shop the Kenmore 9082 Water Filter Now from hive appliances
FAQs
Does the 9082 really cover more than other Kenmore filters?
Yes. It's the only Kenmore filter in this collection carrying NSF 401 certification alongside NSF 42 and 53, which extends coverage to volatile organic compounds and asbestos fibers that other Kenmore codes don't test against.
Is this filter really compatible with non-Kenmore refrigerators?
Yes, genuinely. It shares the EDR2RXD1 filter code with select Jenn-Air, KitchenAid, Amana, Maytag, and Whirlpool refrigerators, so if your fridge takes that code, this filter works.
Why does my filter tray have a locking tab instead of a simple slot?
That's specific to the 9082's twist-out tray design, used on Kenmore and Kenmore Elite bottom-freezer models. It's a different mechanism from the eject or push-button styles used elsewhere in Kenmore's lineup.
How long should I flush the dispenser after installing this filter?
About 4 gallons is recommended, slightly more than some other Kenmore filters, to fully clear air pockets and carbon fines from the new cartridge before regular use.
What if my old filter shows a code like W10609378 instead of 9082?
That's still the same filter. W10609378, W10680605, and P9WB2L are all part numbers that cross-reference to the 9082.
What payment methods do you accept?
Hive Appliances accepts all major cards, Apple Pay, Google Pay, PayPal, and Shop Pay at checkout.